VRH V2 (Variable Ride Height) system for Onewheel GT - NEW!

VRH V2 (Variable Ride Height) system for Onewheel GT - NEW!V2 of the awesome VRH has landed! VRH V2 is now compatible with WTF Rails, and both GT and GTS Boards (Rally rails included)! Introducing the easiest and quickest way to adjust the ride height on your Onewheel GT stock rails, the Variable Ride Height system by Land Surf! Here's the installation video With other axle carriers, you can choose one or two positions for a change in height which isn't all that much adjustability. Plus, you need to spend

V2 of the awesome VRH has landed!

VRH V2 is now compatible with WTF Rails, and both GT and GTS Boards (Rally rails included)! 

Introducing the easiest and quickest way to adjust the ride height on your Onewheel GT stock rails, the Variable Ride Height system by Land-Surf!

Here's the installation video

With other axle carriers, you can choose one or two positions for a change in height - which isn't all that much adjustability. Plus, you need to spend time at home removing a bunch of screws and even the entire wheel.  

Unlike other axle carriers, the VRH are fully 7075 T6 aluminum (2x the strength of 6061). All the hardware is stainless steel for strength and corrosion resistance (and stronger than titanium).

With the VRH you can change your ride height in a minute to any one of 7 positions, with each position moving the board up or down by around 7mm.  The axle is never fully disconnected from the board, so changes are easy and fast.  The system drops the Onewheel Rails up to 1" down, or about .5" up from stock).

Riding to a trail via the streets?  Drop your ride height for the smooth pavement and then quickly raise it to stock or one step higher for the trails! Fast adjustment, and easy to dial in for your perfect ride, every time.

With the VRH system you can precisely dial in any ride height for the terrain while out on a ride, and changing to a new setting takes less than one minute and only 2 screws!  No other ride height adjustment product comes close to this!  With all the others, it’s a back-at-home-only procedure and definitely not while out on a ride.

The third hole from the top corresponds to stock ride height. From there you can go up two steps, or progressively lower the board over 4 stops (the lower holes) for a full drop of about 1" from the stock height at the last setting!

All orders for VRH now receive a free stainless steel GT motor clip retainer to keep your plug on securely!  It's simple to install and much easier to remove if you need to get your wheel out for a tire change or maintenance.

Made from 7075 T6 aluminum for super strength, and then anodized, the VRH not only functions like no other axle carrier, but also looks good doing it!  Logos are laser etched, not silkscreened, so they can’t rub off. 

A set of 4 custom-made, 316 marine grade stainless-steel high strength screws attach the VRH inner brackets directly to the frame, and installation takes only 10-15 minutes. For ease of use, ALL of the screws on the VRH system are M8 threaded and use the same size 5mm hex drive. The new version of the custom frame screws have a much deeper hex socket that eliminates any stripping issues.

IMPORTANT NOTES:  Some fenders and fender deletes will need to be trimmed or Dremmeled (sanded) in order to clear the swingarm and adjuster bolts. We just cut the fender deletes at an angle on a miter saw (and we did a hack job there, yours could be better) and put them on. The Maghandle is incompatible with the VHR brackets.  Rim Saver protectors by TFL fit, but the rail (motor cable side only) must be removed to install the VRH, and not in the way shown in the video.
Once installed, the VRH system is not returnable. 

VRH is fully compatible with our Stone Cold Chillers - and they work very well together!

Each order includes:

• Left & Right VRH Rail Bracket and Swingarm
• 4 custom stainless steel M8 mounting screws
• 2 ride height adjuster M8 screws (stainless steel)
• 6 M8 countersunk screws  (stainless steel)
• 5mm L-key
• A FREE GT motor connector retainer clip (to keep your motor securely connected to the controller).

Patent Pending.